Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
leadership:roadmaps:2016_spring_semester:weatherbox_challenge:spec_sheet [2016/01/26 00:51] kluong [Other parts] |
leadership:roadmaps:2016_spring_semester:weatherbox_challenge:spec_sheet [2021/09/19 21:59] (current) |
||
|---|---|---|---|
| Line 23: | Line 23: | ||
| ===== Main Specifications ===== | ===== Main Specifications ===== | ||
| - | * Microprocessor: [[|Atmel Atmega328P]] | + | * Microprocessor: [[http://www.atmel.com/images/atmel-8271-8-bit-avr-microcontroller-atmega48a-48pa-88a-88pa-168a-168pa-328-328p_datasheet_complete.pdf|Atmel Atmega328P]] |
| * Transciever: [[https://www.adafruit.com/datasheets/XBee%20ZB%20User%20Manual.pdf|XBee Pro Series 2b - RPSMA]] | * Transciever: [[https://www.adafruit.com/datasheets/XBee%20ZB%20User%20Manual.pdf|XBee Pro Series 2b - RPSMA]] | ||
| * Antennae: 2.4 GHz RP-SMA Duck Antennae | * Antennae: 2.4 GHz RP-SMA Duck Antennae | ||
| Line 33: | Line 33: | ||
| * Humidity Sensor: [[https://www.adafruit.com/datasheets/Sensirion_Humidity_SHT1x_Datasheet_V5.pdf|Sensirion SHT11]] | * Humidity Sensor: [[https://www.adafruit.com/datasheets/Sensirion_Humidity_SHT1x_Datasheet_V5.pdf|Sensirion SHT11]] | ||
| * Pressure Sensor: [[https://www.adafruit.com/products/1603|Adafruit BMP-180]] | * Pressure Sensor: [[https://www.adafruit.com/products/1603|Adafruit BMP-180]] | ||
| - | |||
| - | ===== Arduino Breadboard Components ===== | ||
| - | |||
| - | |||
| - | |||
| - | * A breadboard | ||
| - | * 22 AWG wire | ||
| - | * 7805 Voltage regulator (or any other 5v regulator) | ||
| - | * 2 LEDs | ||
| - | * 2 220 Ohm resistors | ||
| - | * 1 10k Ohm resistor | ||
| - | * 2 10 uF capacitors | ||
| - | * 16 MHz clock crystal | ||
| - | * 2 22 pF capacitors | ||
| - | * small momentary normally open ("off") button, i.e. Omron type B3F | ||
| - | |||
| - | |||
| - | ===== Barebones arduino parts ====== | ||
| - | |||
| - | * 2 220 Ohm resistors | ||
| - | * 1 10k Ohm resistor | ||
| - | * 2 10 uF capacitors | ||
| - | * 16 MHz clock crystal | ||
| - | * 2 22 pF capacitors | ||
| ===== Other parts ===== | ===== Other parts ===== | ||
| + | |||
| + | * microprocessor: | ||
| + | * 1 10k Ohm resistor | ||
| + | * 16 MHz clock crystal | ||
| + | * 2 22 pF capacitors | ||
| * humidity sensor: | * humidity sensor: | ||
| Line 75: | Line 56: | ||
| * 1 0.1 uF capacitor | * 1 0.1 uF capacitor | ||
| * Boost Converter: [[http://www.onsemi.com/pub_link/Collateral/NCP1402-D.PDFON|Semiconductor NCP1402-D]] | * Boost Converter: [[http://www.onsemi.com/pub_link/Collateral/NCP1402-D.PDFON|Semiconductor NCP1402-D]] | ||
| + | |||
| + | * XBee headers | ||
| + | * Microprocessor headers | ||
| + | * barrel jack (charging board and solar panel use different sizes) | ||
| + | |||
| + | * housing materials | ||
| + | |||
| + | ===== Parts For Development ===== | ||
| + | |||
| + | |||
| + | * A breadboard | ||
| + | * 22 AWG wire | ||
| + | * Mini USB cable | ||
| + | * FTDI Converter (note: XBee must use softserial) | ||
| + | |||
| + | * Barebones Arduino: | ||
| + | * 2 220 Ohm resistors | ||
| + | * 2 10 uF capacitors | ||
| + | * 2 LEDs | ||
| + | * small momentary normally open ("off") button, i.e. Omron type B3F | ||
| + | * 7805 Voltage regulator (or any other 5v regulator) | ||
| + | * other parts listed under microcontroller | ||
| + | |||
| + | |||
| + | *XBee: | ||
| + | * XBee usb explorer | ||
| + | * XBee breakout board (or something similar) | ||