Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
all_hands_meetings:april_2_2016 [2016/04/02 20:05] cobatake created |
all_hands_meetings:april_2_2016 [2021/09/19 21:59] (current) |
||
|---|---|---|---|
| Line 60: | Line 60: | ||
| ===== CDR Presentation Notes ===== | ===== CDR Presentation Notes ===== | ||
| ==== Overall Presentation Notes ==== | ==== Overall Presentation Notes ==== | ||
| - | * | + | * Avoid putting blocks of code on your slides |
| + | * Convert the code into an algorithm that is more readable | ||
| ==== Instrumentation ==== | ==== Instrumentation ==== | ||
| Line 84: | Line 85: | ||
| ==== Apple Design Team ==== | ==== Apple Design Team ==== | ||
| + | * Five boards ready | ||
| * Temperature sensor pins are CORRECT on the datasheet | * Temperature sensor pins are CORRECT on the datasheet | ||
| * Housing | * Housing | ||
| Line 90: | Line 92: | ||
| * Can configure XBees remotely | * Can configure XBees remotely | ||
| * Cannot program Arduino remotely | * Cannot program Arduino remotely | ||
| + | * BMP085 library can be used with the BMP180 | ||
| ==== Dragonfruit Design Team ==== | ==== Dragonfruit Design Team ==== | ||
| - | * | + | * Four boards ready |
| ==== Cranberry Design Team ==== | ==== Cranberry Design Team ==== | ||
| - | * | + | * Three boards ready |
| + | * Brandon trying to make their own housing | ||
| + | * Thinking of editing Brianne's design | ||
| ==== Firmware Team ==== | ==== Firmware Team ==== | ||
| - | * | + | * Fixing values |
| + | * Voltage divider | ||
| + | * Needed to read data sheets for scaling factors for ADCs | ||
| + | * How values were confirmed | ||
| + | * Confirmed values with old Apple values | ||
| + | * Pressure about 101 kPa | ||
| + | * Humidity about the same for all four boards | ||
| + | * Varied solar irradiance with outdoor light in the room | ||
| + | |||
| + | ==== Forecasting ==== | ||
| + | * Compare to LMS | ||
| + | * Include graphs and block diagrams to make it easier to understand algorithms | ||
| ==== Verification ==== | ==== Verification ==== | ||
| - | * | + | * Will send out board next week |
| + | * Meeting with Garrett at beginning of next week for final design | ||
| ==== XBee Team ==== | ==== XBee Team ==== | ||
| - | * | + | * For rain, test with rain in between the two XBees |
| - | + | * Note temperature and humidity at the time | |
| - | ==== Forecasting ==== | + | * Testing with the antenna wet as if it were raining |
| - | * | + | * 64000 nodes max on a network |
| Line 115: | Line 132: | ||
| * Project Badger | * Project Badger | ||
| * Testing validity of smart outlet data readings | * Testing validity of smart outlet data readings | ||
| - | + | * Team Asteroid | |
| - | ==== Tryston's Presentation Comments ==== | + | * About a week behind |
| + | * Team Nova | ||
| + | * Housing took 8 hours on lowest resolution | ||
| + | * Can ask Brandon for help | ||
| + | * Team Quasar | ||
| + | * Scheduled to finish on time | ||
| + | * Team Black Hole | ||
| + | * XBee antenna should be hanging off the board | ||
| + | * Not using current sensor | ||
| + | * Do pressure in kPa | ||
| + | * Warning that XBee may take a while | ||
| + | * Team Rocket | ||
| + | * Rx and Tx need to be switched | ||
| + | * Rx and Tx are in reference to the part | ||
| + | * Need to be switched from Xbee to Arduino | ||