Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
weatherbox:team_mango:start [2017/11/07 02:08] mcacal [Notes] |
weatherbox:team_mango:start [2021/09/19 21:59] (current) |
||
---|---|---|---|
Line 3: | Line 3: | ||
==Team Leader: Isaiah Aribal== | ==Team Leader: Isaiah Aribal== | ||
- | {{weatherbox:team_mango:yzmlegj.mp4?500}} | + | {{ :weatherbox:team_mango:img_1510.jpg?nolink&400 |}} |
Line 38: | Line 37: | ||
*[[.: Week 8 - October 23 & 25, 2017]] | *[[.: Week 8 - October 23 & 25, 2017]] | ||
*[[.: Week 9 - October 30 & November 1, 2017]] | *[[.: Week 9 - October 30 & November 1, 2017]] | ||
+ | *[[.: Week 10 - November 6 & 8, 2017]] | ||
+ | *[[.: Week 11 - November 13 & 15, 2017]] | ||
+ | *[[.: Week 12 - November 20 & 22, 2017]] | ||
+ | *[[.: Week 13 - November 27 & 29, 2017]] | ||
+ | *[[.: Week 14 - December 4 & 6, 2017]] | ||
+ | ===== Presentation PDF ===== | ||
+ | *{{ :weatherbox:team_mango:project_proposal_presentation_-_team_mango_fall17.pdf |Project Proposal}} | ||
+ | *{{ :weatherbox:team_mango:pdr_presentation_-_team_mango_fall17.pdf |Preliminary Design Review}} | ||
+ | *{{ :weatherbox:team_mango:cdr_presentation_-_team_mango_fall17.pdf |Critical Design Review}} | ||
+ | *{{ :weatherbox:team_mango:final_presentation_-_team_mango_fall17.pdf |Final Presentation}} | ||
====== Notes ====== | ====== Notes ====== | ||
- | For future 296 Reference -M.C. | + | For future 296 Reference |
=== Sensors === | === Sensors === | ||
* Sensors are outdated in REIS 296 Schematics. | * Sensors are outdated in REIS 296 Schematics. | ||
Line 59: | Line 69: | ||
* My mistake was using label to wirelessly connected but wasn't actually connected | * My mistake was using label to wirelessly connected but wasn't actually connected | ||
* Used Pinheaders in order to use Breakout Boards | * Used Pinheaders in order to use Breakout Boards | ||
+ | * Beware of the voltage regulators, Schematic isn't corresponding to datasheet | ||
+ | * Recommend making personalized parts | ||
=== PCB Design === | === PCB Design === | ||
Line 66: | Line 78: | ||
=== Testing === | === Testing === | ||
* Team Pineapple tried to test Microprocessor on breadboard instead of Arduino. Failure to communicate. | * Team Pineapple tried to test Microprocessor on breadboard instead of Arduino. Failure to communicate. | ||
- | * The problem was fixed by setting 2 parameters something like ISP and ardiuno/generinuo uno AND hitting the reset button between the "compliing" and "running" command. | + | * The problem was fixed by setting 2 parameters something like ISP and Ardiuno/Generinuo Uno AND hitting the reset button between the "compliing" and "running" command. |
- | * | + | |
+ | === Improvements & Future Work === | ||
+ | * Adjustment of housing dimensions can be made once the physical board is printed. | ||
+ | * Currently no software improvements. | ||
+ | * SMD parts can replace all through-hole parts. |