Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
weatherbox:guava:week_12_-_april_10_2017 [2017/04/13 02:07] dkvilla created |
weatherbox:guava:week_12_-_april_10_2017 [2021/09/19 21:59] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Week 12 - April 12, 2017 ====== | ====== Week 12 - April 12, 2017 ====== | ||
| ===== Updates ===== | ===== Updates ===== | ||
| - | * Parts order came in | + | * Submitted 496 Abstract to the EE assistant for use in the 496 pamplet/program thing. |
| + | * Objective, Abstract, and Team Members | ||
| + | |||
| + | ==== Parts Order ==== | ||
| + | Parts order came in - yay. Time to test. | ||
| * BME280 | * BME280 | ||
| - | * ATmega1284P - DIP and TQFN | + | * Using the Adafruit testing code from their github with an Arduino Uno to verify how/that it works |
| - | * | + | * Going to hook it up using I2C first then SPI |
| + | * I2C wiring - Using an Arduino Uno and the test code compiles and works. | ||
| + | * Reads Temperature/Pressure/Altitude/Humidity | ||
| + | * SPI wiring - Using the same Arduino Uno the test code compiles and works | ||
| + | * Dylan's code is to use with the whole board hooked up in the firmware of the whole box like the driver for the sensor to use in whole system | ||
| + | * ATmega1284P - DIP and TQFN packages. | ||
| + | * Need to breadboard a DIP one to start testing its functionalities and differences between the 328P | ||
| + | |||
| + | ==== Design/Research ==== | ||
| + | * Rain sensor | ||
| + | * We have a solar sensor and wind sensor. Why not rain sensor? | ||
| + | * Look into creating a DIY version of rain sensor. | ||
| + | * Leads that short when there is a conductor (rain water) present. | ||
| + | * Helpful link maybe - http://www.instructables.com/id/Arduino-Modules-Rain-Sensor/\ | ||
| + | |||
| + | ===== Reminders ===== | ||
| + | * SCEL's participation in CoE's Open House is canceled due to a "full program" | ||
| + | * April 29th, Final Presentation | ||
| + | * Final Paper - 4000 words - should start breaking up the paper into sections for people to write about now | ||
| + | * Topics | ||
| + | * Objective | ||
| + | * Project Description | ||
| + | * Block Diagram | ||
| + | * Hardware | ||
| + | * Firmware | ||
| + | * Parts | ||
| + | * BME | ||
| + | * ATmega | ||
| + | * Programmer circuit | ||
| + | * SP-215 | ||
| + | * Charging Chip | ||
| + | * Xbee | ||
| + | * Firmware? | ||
| + | * Switches | ||
| + | * GPS | ||
| + | * | ||
| + | * Design Choices | ||
| + | * 3.3V vs 5V | ||
| + | * BME | ||
| + | * ATmega1284 | ||
| + | * Why we went with this one and not another one | ||
| + | * pros and cons of each of these items | ||
| + | * Board Layout | ||
| + | * GPS/RTC | ||
| + | * Problems/Solutions | ||
| + | * Time | ||
| + | * Hardware stuff | ||
| + | * Documentation | ||
| + | * How we did it | ||
| + | * Future Work | ||
| + | * Plans to continue | ||
| + | * What else were missing | ||
| + | * What we would have done differently | ||
| + | * What we could change | ||
| + | * Conclusion | ||
| + | * Where we are at now | ||
| + | * where we wanted to be | ||
| + | * Where we plan to go from here | ||
| + | * Experiences | ||
| + | * Lessons learned | ||
| + | |||
| + | [[weatherbox:guava:meeting_minutes|Back to Guava's Meeting Minutes]]\\ | ||